The Post and Base

Hello Gang.

        Back from a weekend away with friends, and it is time to look at removing the ladder, lattice post and the base from the fret and building the main post structure. You will also require the ladder stand off bracket and the landing bracket (they will be used in the next instalment).

        I normally try to build structures on a good foundation and the lattice post signal is not different. I cut a small piece of 9 mm craftwood (you can use anything that you have lying around), approximately 50 mm x 25 mm.  On this base we can build the signal from the base up. The base also serves as a place to attach a servo if you wish to fit one to operate your signal.

        If you now remove the the previously drilled ladder stiles, and grab a couple of lengths of 0.3 mm brass wire, which needs to be cut into small lengths. Using a sanding block, sand the excess tab material of the sides of the ladder stiles and try to keep the stiles straight as bending them would not go well at this stage. Locate the ladder stiles in the KRM Misc 004 ladder forming jig and follow the latest blog that I have set up at

http://krmodelsholadderformingjig.blogspot.com.au/.

        This blog gives you a great blow by blow of how to use the ladder forming jig. which I will not repeat here. For this kit I make the ladder 12 scale inches.

The finished ladder soon to be located onto the signal and base.

The Ladder Base and the Timber Block.

The base prior to drilling on the corners for location purposes
(modifications to Version 2 will incorporate these holes)

The timber base  made from craftwood, but any material that you have
 lying around, can be used.

        The base of the signal, is located about 15 mm from the outer edge of the block. with the ladder location holes facing to the right.

        Firstly you will need to drill 4 holes (0.5 mm drill) in the corners of the base, just in from the edge (a modification to the signal kit will be done in Version 2).  Locate the base and drill the timber base through the signal base for brass pins to hold the base down to the timber.  The other hole that needs drilling is the actuator hole which sits to the right front of the signal post location holes, drill it out 0.5 mm then drill the timber base to 1 mm so that it has some clearance for any actuation  linkage.

        You can use track pins if you prefer or the lace pins are available from KRM  (KRM Misc 002). Cut 4 lace pins about 6 mm to 8 mm long. File the tips so that they are sharp, and check the fit of the pins into the base. Remove the pins and signal base and place aside for securing to the post later on.

The signal base with the cut down pins ready to be located in the base.

The signal base located temporarily, using shortened lace pins.

 The Lattice Signal Post.

        The lattice post etch has 6 small tabs that will allow the etch to fold very easily. You can use a Hold and Fold tool, but to be honest, it is not necessary. Let us have a look at the etch. You will notice that the top of the etch had 2 long half etched sections, and the other 2 have 2 short half etched sections. These half etched sections are there to simulate the timber part of the signal post. Refer to the previous photos to give you an idea of how the signal is orientated. When you fold the post etch, ensure that you only fold it once, with the half etched sections to the outside of the signal. Fold the signal so the the top hole and the bottom hole are square.  The 6 small tabs on each fold line are half etched on the inside to allow for easy folding.

The lattice post signal just after removing from the fret and cleaning up the
tabs that hold the part in the fret.

      There is a reason that this kit is made from nickel silver, and that reason is simply because it solders very easily. The solder flows well and makes the modellers job much easier. I use standard fine resin core solder from Dick Smiths with Carr's Red flux. Others have their own preferred options, but I find this works for me.

      Starting with the main joint, solder the joint completely using very little solder and when finished do the same with the other 3 fold lines with the tabs.  When finished wash the post with warm water and dry, them using very fine sanding blocks, clean up the joints and the post faces. If you run you fingers down the edge of the post, you can feel the tabs slightly protruding from the corners, you can sand these away if you like, but they will be difficult to see on the finished signal, so it is your choice. The finished post should be square both top and bottom and the top should be able to accommodate the finial on the inside, which means that the finial base will need to be filed to fit.

The finished post after cleaning up and ready to be inserted into the base.

        The orientation of the signal post is really important. and should be as per the photos previously published.  The hole at the very top of the post is for the signal arm, and should be located so that it is facing the ladder slots in the signal base.

        Some modellers have said that the signal post feet don't fit into the base, if you drill as per the instructions. However this is not true, as the feet of the post are smaller than 0.4 mm and they just need to be manipulated to fit. The base below was drilled as per the instructions, and the legs protrude through to give a nice solid fitting into and through the base. Solder the feet into the base from underneath, ensuring that the post is straight and square to the base. When you are happy that the post is straight, allow the solder to set, and file the excess from under the base, leaving it flat to sit on the timber base.

The post legs showing through the base, they are made longer than necessary to
 allow for this type of protrusion.

The  feet can be clearly seen here, protruding through the base.

The signal post soldered to the base giving it a good support.

     

The base, after solder and excess leg material removed, ready to be located
on the base

        In the next instalment, we will  fold up the brackets and place the ladder onto the signal, and fit the finial.

        Until then it is buy for now, please leave any comments that you like, or any questions that you need answered. More than happy to help to make this kit into a fully working signal.

Regard Keiran Ryan